Change or rekey · Bendale
Smart Lock Installation in Bendale
There are four copies of the front-door key floating around: one with the cleaner, one with a neighbour, one on a hook at your parents' place, and one you honestly cannot account for.
In plain words
Smart lock installation puts an electronic deadbolt or lever on your door that opens with a code, a phone, a fob or a fingerprint, and, on some models, a conventional key too. The locksmith confirms you control the property, measures the door and its holes, and makes sure the bolt travels freely, because a battery motor has less strength than a hand. The hardware is fitted with a solid strike, the maker's specified batteries go in, and the lock is set up under your own account. You leave with codes working and, on a keyed model, the override key tested and the old key retired.
How the visit goesArthritis has made the small house key hard to grip and turn, especially with gloves on in January. Pressing a few buttons, or tapping a fob against the lock, would make coming home in winter far easier.
Smart Lock Installation
How the visit goes
Storm doors, sun and weather on the entrance
The outside of the lock lives in the weather, so the locksmith looks at what the entrance throws at it. A storm door with full glass can turn the space between the doors into an oven on a July afternoon, and electronics have a temperature ceiling; a vented storm door or a model rated for that exposure solves it. A keypad that faces prevailing wind collects driving snow and freezing rain, which argues for a covered entry or a lock with a shielded touch surface. Salt spray from a nearby driveway attacks finishes over time. None of these rule out a smart lock; they steer the choice of model, finish and mounting.
Fitting the bolt, the body and the strike
With the door ready, the mechanical parts go in first. The new bolt is set to the door's backset and slid into the edge bore with its face plate flush. The outside assembly, keypad or touch surface, is placed with its cable fed through the cross bore, and the inside mounting plate is fixed so the two halves clamp the door without twisting. Screws are driven by hand rather than with an impact driver, because an over-tightened housing binds the motor. The interior unit is seated on the plate and the tailpiece aligned so the thumb-turn and the motor share the same travel. A reinforced strike with long screws replaces the light original.
A written record without your secrets in it
The visit closes with a plain note of what was done: the model fitted, the door corrections made, whether the strike was reinforced, which override cylinder was rekeyed and how many keys were cut, and which other doors were brought onto the same key. What the note never contains is a code, a password or a login; those exist only on your account and in your head. For a tenant, that record is the thing to share with a landlord so both sides know what hardware is on the door and that a working way in exists. For an owner, it simply goes in the folder with the house documents.
Smart Lock Installation
In the van
Hinge shims and long hinge screws
Adjustable-backset bolt and faceplate
Smart deadbolt or smart lever set
Dry PTFE lubricant
Hole saw, spade bit and drilling jig
Smart Lock Installation
What affects the quote
Condition and fit of the door
A door that already closes true with standard holes is the simplest install. One that needs hinges shimmed, a strike pocket deepened or holes enlarged adds preparation time, and that work is quoted as its own line.
Supplying the lock yourself
If you have already bought a lock, the quote covers fitting and setup only, with a note on whether the chosen model suits your door; if the locksmith supplies it, the hardware is listed alongside.
Rekeying the override cylinder and other locks
Repinning the smart lock's backup cylinder to a new key, cutting the keys and bringing the remaining mechanical locks onto the same key are each counted per cylinder and per key.
What to have ready
- Should the door lock itself after it closes?
- Roughly how thick is the door?
- Which other doors should share the same key or the same system?
Smart Lock Installation: questions
QuestionsDoes the locksmith keep any of my codes or my account details?
No. The administrator account is created by you, on your phone, with your email, and the codes are entered by you or read out by you and typed while you watch. The service note records the model, the door work and the keys cut, never a code or a password. If a technician programmed a temporary code for testing, it is deleted in front of you before the visit ends.
I am a landlord. Are smart locks a good fit for my rental?
They suit turnover well: a departing tenant's code is deleted and a new one created without cutting keys or wondering about copies. Two things to plan for. The tenant in place must always have a working way in, which usually means their own code plus a key to the override cylinder, and any lock change on an occupied unit is done with the tenant's knowledge. Set the administrator account up under the property, not a departing employee, so control stays with you.
Does the lock still work if the internet goes down?
Yes for the things that matter at the door. Codes, fobs, fingerprints and the key talk to the lock directly, and schedules stored in the lock carry on, so you get in and out normally through a router reboot or an outage. What pauses is remote control from far away and the alerts, which return when the connection does. The locksmith will name exactly which features on your model need the network so there are no surprises.
Related services
- Deadbolt InstallationThe old deadbolt has grown lazy.
- Lock Replacement & UpgradeThe house is fifteen years old and every exterior door still wears the light hardware the builder fitted: a short bolt, a thin strike held by two small screws, and a knob lock that never suited a street entrance.
- Vintage Mortise Lock ServiceThe interior bedroom doors on the second floor have the original mortise latches, and none of them close any more.